QUADSPI device tree configuration

Article purpose

本文介绍如何在将 QUADSPI internal peripheral 分配给 Linux^®操作系统时对其进行配置。 在这种情况下，它由MTD framework控制.

使用device tree 机制执行配置，该机制提供由STM32 QUADSPI Linux驱动程序和MTD框架使用的QUADSPI外围设备的硬件描述。

如果外围设备已分配给另一个执行上下文，请参阅[[[How to assign an internal peripheral to a runtime context]] 文章，了解有关外围设备分配和配置的指南。

DT bindings documentation

QUADSPI设备树绑定由以下组成：

• generic SPI-NOR / SPI-NAND Flash memory bindings .

• QUADSPI driver bindings .

在接下来的章节中，SPI-NAND绑定只与ecosystem release ≥ v1.1.0{{#set:Ecosystem release=revision of a previous flow 1.1.0}} 兼容。

DT configuration

该硬件描述是“STM32微处理器”设备树文件（扩展名为.dtsi）和“板子”设备树文件（扩展名为.dts）的组合。 有关设备树文件分割的说明，请参见Device tree. STM32CubeMX可用于生成板设备树。 有关详细信息，请参阅How to configure the DT using STM32CubeMX 。

DT configuration (STM32 level)

QUADSPI外设节点位于``stm32mp157c.dtsi 文件。

   qspi: spi@58003000 {                                      Comments
       compatible = "st,stm32f469-qspi";
       reg = <0x58003000 0x1000>,                            --> Register location
             <0x70000000 0x10000000>;                        --> Memory mapping address
       reg-names = "qspi", "qspi_mm";
       interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;        --> The interrupt number used
       dmas = <&mdma1 22 0x10 0x100002 0x0 0x0 0x0>,         --> DMA specifiers 
              <&mdma1 22 0x10 0x100008 0x0 0x0 0x0>;
       dma-names = "tx", "rx";
       clocks = <&rcc QSPI_K>;
       resets = <&rcc QSPI_R>;   
       status = "disabled";
   };

与STM32相关的该设备树部分应保持原样，客户不应对其进行修改。

DT configuration (board level)

QUADSPI外设最多可连接2个SPI-NOR闪存。

SPI-NOR闪存节点 必须是QUADSPI外设节点的子级。

   &qspi {                                                   Comments
       pinctrl-names = "default", "sleep";                   --> For pinctrl configuration, please refer to Pinctrl device tree configuration
       pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
       pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
       reg = <0x58003000 0x1000>,
             <0x70000000 0x4000000>;                         --> Overwrite the memory map to the Flash device size, avoid the waste of virtual memory that will not be used
       #address-cells = <1>;
       #size-cells = <0>;
       status = "okay";                                      --> Enable the node

       flash0: mx66l51235l@0 {     
           compatible = "jdec,spi-nor";                                  
           reg = <0>;                                        --> Chip select number
           spi-rx-bus-width = <4>;                           --> The bus width (number of data wires used)
           spi-max-frequency = <108000000>;                  --> Maximum SPI clocking speed of device in Hz
           #address-cells = <1>;
           #size-cells = <1>;
       };
   };

DT configuration example

以下示例显示了在连接1个SPI-NAND闪存和1个SPI-NOR闪存时如何配置QUADSPI外设。

   &qspi {                                                    
       pinctrl-names = "default", "sleep";                    
       pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
       pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
       reg = <0x58003000 0x1000>,
             <0x70000000 0x4000000>;                          
       #address-cells = <1>;
       #size-cells = <0>;
       status = "okay";

       flash0: mx66l51235l@0 {                                 
           compatible = "jdec,spi-nor";
           reg = <0>;
           spi-rx-bus-width = <4>;
           spi-max-frequency = <108000000>;
           #address-cells = <1>;
           #size-cells = <1>;
       };

       flash1: mt29f2g01abagd@1 {                             
           compatible = "spi-nand";
           reg = <1>;
           spi-rx-bus-width = <4>;
           spi-tx-bus-width = <4>;
           spi-max-frequency = <133000000>;
           #address-cells = <1>;
           #size-cells = <1>;
       };
   };

How to configure the DT using STM32CubeMX

STM32CubeMX 工具可用于配置STM32MPU设备并获取相应的platform configuration device tree文件。
STM32CubeMX可能不支持上述DT bindings documentation p段落中描述的所有属性。 如果是这样的话，该工具会在生成的设备树中插入“”User Sections“”。 然后可以编辑这些部分以添加某些属性，并将它们代代相传。 有关详细信息，请参阅STM32CubeMX 用户手册。

References

Please refer to the following links for full description:

<securetransclude src="ProtectedTemplate:ArticleBasedOnModel" params="Peripheral or framework device tree configuration model"></securetransclude> <securetransclude src="ProtectedTemplate:PublicationRequestId" params="8899 | 2018-10-10 | AlainF"></securetransclude>