OTG device tree configuration

Article purpose

本文介绍了在将OTG internal peripheral 分配给Linux^® OS时如何进行配置。 在这种情况下，它由 USB framework控制。

使用 device tree 机制执行配置。

它由“ OTG Linux驱动程序” 用于在USB framework中注册相关信息。

DT bindings documentation

"Platform DesignWare HS OTG USB 2.0控制器设备树绑定" document represents the OTG（DRD）控制器。

“通用USB设备树绑定” 文档表示通用USB属性，由USB framework 提出，例如最大速度，dr_mode ...

DT configuration

This hardware description is a combination of the STM32 microprocessor device tree files (.dtsi extension) and board device tree files (.dts extension). See the Device tree for an explanation of the device tree file split.

STM32CubeMX can be used to generate the board device tree. Refer to How to configure the DT using STM32CubeMX for more details.

DT configuration (STM32 level)

The usbotg_hs DT node is declared in stm32mp157c.dtsi.

It is composed of a set of properties, used to describe the OTG controller: registers address, clocks, resets, interrupts...

usbotg_hs: usb-otg@49000000 {
	compatible = "snps,dwc2";
	reg = <0x49000000 0x10000>;
	clocks = <&rcc USBO_K>;
	clock-names = "otg";
	resets = <&rcc USBO_R>;
	reset-names = "dwc2";
	interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
	dr_mode = "otg"; 	 	 	 	/* dr_mode can be overwritten at board level to set a particular mode */
	status = "disabled";
};

This device tree part is related to STM32 microprocessors. It must be kept as is, without being modified by the end-user.

<securetransclude src="ProtectedTemplate:ReviewsComments" params="FGA W902: Later add some examples to fine tune various fifo size (g-rx-fifo-size, g-np-tx-fifo-size, g-tx-fifo-size) depending on the use case: host, gadget eth, gadget mass storage... Maybe part of a dedicated article"></securetransclude>{{#set:Has reviews comments=true}}

DT configuration (board level)

Follow the sequences described in the below chapters to configure and enable the OTG on your board.

OTG supports two PHY interfaces that can be statically selected via DT:

• full-speed PHY, embedded with the OTG controller
• high-speed USBPHYC HS PHY that can be assigned to either the USBH or the OTG controller.

When operating in "otg" or "host" mode, an external charge pump, e.g. 5V regulator must be specified.

Please refer to Regulator overview for additional information on regulators configuration.

DT configuration using full-speed USB PHY

• Enable the OTG by setting status = "okay".
• Use embedded full-speed PHY by setting compatible = "st,stm32mp1-fsotg", "snps,dwc2"
• Configure full-speed PHY pins (OTG ID, DM, DP) as analog via pinctrl, through pinctrl-0 and pinctrl-names.
• Optionally set dual-role mode through dr_mode = "peripheral", "host" or "otg" (default to "otg" in case it is not set)
• Optionally set vbus voltage regulator for otg and host modes, through vbus-supply = <&your_regulator>

DT configuration using high-speed USB PHY

• Enable the OTG by setting status = "okay".
• Select USBPHYC port#2 by setting phys = <&usbphyc_port1 0>; and phy-names = "usb2-phy";
• Optionally configure OTG ID pin as analog via pinctrl, through pinctrl-0 and pinctrl-names.
• Optionally set dual-role mode through dr_mode = "peripheral", "host" or "otg" (default to "otg" in case it is not set)
• Optionally set vbus voltage regulator for otg and host modes, through vbus-supply = <&your_regulator>

Please refer to USBPHYC device tree configuration for additional information on USBPHYC port#2 configuration

DT configuration examples

DT configuration example as full-speed OTG

The example below shows how to configure full-speed OTG, with the ID pin to detect role (peripheral, host):

• OTG ID and data (DM, DP) pins: use Pinctrl device tree configuration to configure PA10, PA11 and PA12 as analog input.
• Use integrated full-speed USB PHY by setting compatible
• Dual-role (dr_mode) is "otg" (e.g. the default as unspecified)
• Use vbus voltage regulator

# part of pin-controller dt node
usbotg_hs_pins_a: usbotg_hs-0 {
	pins {
		pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */            /* configure 'PA10' as ANALOG */

	};
};

usbotg_fs_dp_dm_pins_a: usbotg-fs-dp-dm-0 {
	pins {
		pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* OTG_FS_DM */
			 <STM32_PINMUX('A', 12, ANALOG)>; /* OTG_FS_DP */
	};
};

&usbotg_hs {
	compatible = "st,stm32mp1-fsotg", "snps,dwc2";                            /* Use full-speed integrated PHY */
	pinctrl-names = "default";
	pinctrl-0 = <&usbotg_hs_pins_a &usbotg_fs_dp_dm_pins_a>;                  /* configure OTG ID and full-speed data pins */
	vbus-supply = <&vbus_otg>;                                                /* voltage regulator to supply Vbus */
	status = "okay";
};

DT configuration example as high speed OTG

The example below shows how to configure high-speed OTG, with the ID pin to detect role (peripheral, host):

• OTG ID pin: use Pinctrl device tree configuration to configure PA10 as analog input.
• Use USB HS PHY port#2, with the UTMI switch that selects the OTG controller
• Dual-role mode (dr_mode) is "otg" (e.g. the default as unspecified)
• Use vbus voltage regulator

# part of pin-controller dt node
usbotg_hs_pins_a: usbotg_hs-0 {
	pins {
		pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */            /* configure 'PA10' as ANALOG */

	};
};

&usbotg_hs {
	compatible = "st,stm32mp1-hsotg", "snps,dwc2";
	pinctrl-names = "default";
	pinctrl-0 = <&usbotg_hs_pins_a>;                                          /* configure OTG_ID pin */
	phys = <&usbphyc_port1 0>;                                                /* 0: UTMI switch selects the OTG controller */
	phy-names = "usb2-phy";
	vbus-supply = <&vbus_otg>;                                                /* voltage regulator to supply Vbus */
	status = "okay";                                                          /* enable OTG */
};

How to configure the DT using STM32CubeMX

The STM32CubeMX tool can be used to configure the STM32MPU device and get the corresponding platform configuration device tree files.
The STM32CubeMX may not support all the properties described in the above DT bindings documentation paragraph. If so, the tool inserts user sections in the generated device tree. These sections can then be edited to add some properties and they are preserved from one generation to another. Refer to STM32CubeMX user manual for further information.

References

Please refer to the following links for additional information:

<securetransclude src="ProtectedTemplate:ArticleBasedOnModel" params="Peripheral or framework device tree configuration model"></securetransclude> <securetransclude src="ProtectedTemplate:PublicationRequestId" params="10336 | 2019-01-16 | AlainF"></securetransclude>